Laminated Veneer Lumber (LVL) is one of the most common scaffold plank styles used on a jobsite requiring stagging. LVL SCAFFOLDING PLANK(plank) meet all conformance standards for OSHA and are tested rigorously by our factory. It is very versatile walk boards and is usable in all conditions and is able to handle the stress of heat, cold, snow and rain. Not to mention the heavy loads and constant cycling of being put onto a job, being taken back down and repeating that process again and again. LVL SCAFFOLDING PLANK(plank) provide excellent strength and consistency, it also have water-resistant adhesives and the ends are sealed to help slow moisture uptake. All boards(planks) have a stamp showing that it confirms to OSHA’s standards, manufacturing date,a proof-test confirming that it has been load tested.

1. Product Introduction of LVL Scaffolding Plank

Pine LVL Scaffolding Plank are mainly used in the construction field. The main raw materials are mainly imported New Zealand radiation pine and tynea phenolic glue. They have the characteristics of waterproof, anti-corrosion, no deformation, and non-warping etc. The design of four corner chamfering and the treatment of waterproof end are easy for construction workers to carry and handle. The side spray code can be customized according to customer requirements. Its strength and toughness is three times that of solid wood sawn timber. The size is arbitrarily customized according to customer requirements. The maximum size is 9.6 meters length, 1.5 meters width and 300 mm thickness.

2. Product Parameter of LVL Scaffolding Plank

LVL SCAFFOLDING PLANK

1. Scaffold lvl board,scaffolding lvl plank by pine lvl plywood Material:pine

2. Glue:wbp (waterproof glue )

3. Size:38x225x3900mm or customized

4. Moisture content: under 15%

5. Density:630 kgs/cbm

6. Surface:sanding well or Painting

7. Thickness tolerance: +/- 0.5mm

3. Product Typical Feature of LVL Scaffolding Plank

Product Feature of LVL Scaffolding Plank

JEWOO LVL SCAFFOLDING PLANK 

* Flat, beautiful, Low moisture content, Without moldy effect;

* High design values for bending, stiffness and shear strength ;

* Resists shrinking, warping, splitting and checking ;

* Ordinary nail assembly – installs as easily as ordinary lumber;

* High strength-to-weight ratio – more than 40 stronger than solid sawn

Application of LVL Scaffolding Plank

4. Product Qualification of LVL Scaffolding Plank

The Qualification of LVL Scaffolding Plank as below:

5. Production-line,Package and Loading

Production line of LVL Scaffolding Plank

1) Veneer cutting, the cutting methods can be quater cut or rotary cut. This process produce different grades of veneers for plywood production.

2) Veneer drying, the moisture content in the veneer is critical for bond strength of a plywood panel.

3) Glue spreading, glue are spreaded on the veneer evenly with a glue spreader. The thinner the better.

4) Billeting,billeting is a professional term in plywood production. It a system method to lay up the veneers based on plywood structure, thickness and layer numbers.

5) Ageing,the billeted veneers are stacked for 15minutes before cold press. This process is called aging.

6) Could press(Pre-Press),Cold press is the first step to make the veneers into a flat board.The stack are usually 1meter high. Pressure 0.8-1.0 MPa. Pre-press time 15-20 minute.

7) Hot press, Liquid glue has no bonding strength,the glue must be cured in order to get bond strength.The curing requires pressure and high temperature.

8) Surface Laminating,this is the second time hot press of 2 times hot press. Even though its time and pressure is less than the 1st hot press.

Package of LVL Scaffolding Plank

Loading of LVL Scaffolding Plank